Skip to content

Open 24/7 · Free pickup in all seven emirates · We buy cars in any condition

How to Change Spark Plugs: A Step-by-Step DIY Guide

A careful step-by-step guide to replacing spark plugs yourself: the tools, the right plug, removing coils, gapping, correct torque and the mistakes that damage engines.

CCarScrap.ae teamUpdated 14 Nov 20263 min read
How to Change Spark Plugs: A Step-by-Step DIY Guide
In this article

Replacing spark plugs is one of the more approachable maintenance jobs on a petrol engine. On many four-cylinder cars it takes under an hour with basic tools. On some V6 and V8 engines the rear plugs sit under the intake manifold, and the job is better left to a workshop. Read the owner's or service manual before you start, and if anything here differs from it, follow the manual.

When to change them

Manufacturers set the interval by plug type and engine. Copper plugs need changing much sooner than platinum or iridium plugs, which can last a long distance. Change them earlier if you notice misfires, rough idling, hard starting or higher fuel consumption. Our companion article on signs your spark plugs need attention covers the symptoms in detail.

What you need

  • The correct plugs: the type and part number listed in the manual or by the parts supplier for your exact engine.
  • A ratchet, extensions and a spark plug socket of the right size (one with a rubber insert holds the plug).
  • A torque wrench.
  • A gap gauge, if your plugs need gapping.
  • Compressed air or a soft brush, and a small screwdriver or trim tool for clips.
  • Dielectric grease for coil boots, if the manual recommends it.

Step-by-step

1. Work on a cold engine

Aluminium cylinder heads expand when hot, and removing plugs from a hot engine can damage threads. Let the engine cool completely, which in UAE summer can take a while if the car has been in the sun.

2. Disconnect the battery if advised

Some manuals recommend disconnecting the negative terminal. Do so if yours does.

3. Remove the engine cover and coils

Most modern engines have a separate ignition coil on each plug. Unplug the electrical connector, remove the bolt holding the coil and pull the coil straight up. Older engines use plug leads; pull them by the boot, not the wire, and label them so they go back in the right order.

4. Clean around the plug wells

Blow out dust and sand with compressed air before removing a plug, so nothing falls into the cylinder.

5. Remove the old plug

Turn the plug anticlockwise with the socket and extension. If it feels very tight or gritty, stop and seek advice rather than forcing it.

6. Read the old plug

Light tan deposits are normal. Black soot, oily deposits or white blistering can point to fuelling, oil consumption or overheating problems worth investigating.

7. Check the gap

Many iridium and platinum plugs are pre-gapped and their fine tips can be damaged by adjustment. Only adjust if the manufacturer says so, and use the specified gap.

8. Fit the new plug

Start the new plug by hand to avoid cross-threading; a short length of rubber hose over the plug end helps. Do not use anti-seize unless the plug or vehicle manufacturer recommends it, as it changes the effective torque.

9. Torque correctly

Tighten to the specified torque. Too loose and the plug can overheat or come loose; too tight and you risk damaging the threads in the head.

10. Refit the coils and test

Refit each coil firmly, reconnect the connectors and the battery, and start the engine. It should idle smoothly. A flashing check-engine light means a misfire; recheck the coil connections.

Common mistakes

  • Mixing up plug leads on older engines.
  • Dropping debris into an open cylinder.
  • Using the wrong plug heat range.
  • Over-tightening without a torque wrench.

When maintenance is no longer worth it

New plugs fix many rough-running engines. If misfires continue because of low compression, a damaged head or a failing engine, the repair may cost more than the car is worth. In that case, CarScrap.ae buys the car as it is, with free pickup across the UAE and payment by cash or bank transfer. Call or WhatsApp us, or ask for a cash offer. See also our UAE car maintenance guide, selling in Sharjah and our contact page.

The information in this article is general guidance, not advice for your specific project. See our Terms.

Frequently asked questions

It depends on the plug type and engine. Follow the interval in your service manual; iridium and platinum plugs last much longer than copper ones.
Many iridium and platinum plugs come pre-gapped and should not be adjusted. Check the manufacturer's instructions.
No. Let the engine cool fully to avoid damaging the threads in an aluminium cylinder head.
The cause may be a coil, injector, vacuum leak or low compression. Have it diagnosed before spending more.

Was this article helpful?

C

Written by

CarScrap.ae team

369 articles

Get new articles by email

Practical tips now and then. Confirm by email, unsubscribe any time.

Got a car you want gone?

Free pickup, payment on the spot, 24/7 across the UAE.

Or call us+971507395522

Serving